Tips on how to set up Ring Ring 2 video ringtone

May 18, 2019 By Lisa

Tips on how to set up Ring Ring 2 video ringtone

Even in case you have no handyman expertise, putting in a brand new video doorbell is straightforward. Doorbell Video Ring 2 has a streamlined set up course of that anybody can carry out in below 30 minutes. As well as, a lot of the instruments you will want are already within the set up equipment. Right here's easy methods to set up a Ring Ring 2 video ringtone.

Preparation

Prior to installing your new bell, you have to deviate from three issues.

First, you might want to cost the Ring Video Doorbell battery. Take away the silver a part of the case (the entrance panel) and slide the battery out of the underside of the doorbell. Subsequent, join the cost cable provided with the battery and plug it right into a wall outlet till solely the inexperienced gentle on the battery case is lit. When completed, put it again within the doorbell till you hear a click on, however don’t put the entrance panel again for the second.

Video ring doorbell 2 battery Terry Walsh / Digital Tendencies

Second, flip off your present doorbell by activating the corresponding swap within the breaker of your private home. For those who have no idea which swap is the correct one, activate the primary swap. This may stop undesirable electrical shock when putting in your new doorbell.

Third, set up the applying and comply with the on-screen directions to attach your Ringtone video doorbell 2 with the Wi-Fi of your private home.

Take away the outdated bell

Then you’ll want to take away your outdated bell. Use the screwdriver included with the set up equipment to take away the screws and pull the doorbell away from the wall. It’s best to discover two wires on the again of the doorbell wrapped round two screws. Loosen the screws and take away the bell wires.

Connect the video ringing tone

To put in the Ring, you might want to seize a pencil, the set up equipment screwdriver and a drill if the set up holes don’t match these of your outdated bell (most probably they won’t be) . In any other case, you’ll simply want the screwdriver.

If the holes don’t line up, maintain the Ring ring towards the wall the place you’ll set up it and use the pencil to mark the brand new screw holes on the wall. Then use your drill to drill the brand new holes. Place the plastic anchors provided with the bell within the drilled holes.

Ring

Then loosen the screws on the again of the ring. Wrap the bell wires across the screws on the again of the Ring Bell and tighten the screws.

If the cables are too quick, recuperate the extensions within the set up equipment. Slide the underside of an extension twine and wire out of your wall right into a wire nut from the equipment (they seem like grey caps) and rotate it clockwise. 39, a watch to attach the 2 wires. Then merely slide the wire extensions below the screws and tighten them.

In case your outdated doorbell was digital, you will want to put in the diode supplied with the set up equipment. The diode appears like a wire with a black pearl within the center. To put in the diode, take away the doorbell screws, slide them into the wire holes, after which screw them again into their holes earlier than winding the wires. Tip: In case your Ring Ring doesn’t work after set up, take away the LED, flip it over and reinstall it. Watch the video under for extra data on putting in the diode.

Connect the bell to the wall utilizing the screws supplied. Your ring must be 4 toes off the bottom to work correctly. For those who set up it larger, place the set up nook supplied with the doorbell behind the highest of the unit earlier than screwing it to the wall. This may ring the bell barely downwards and thus present an ideal view of your gateway.

End

Terry Walsh / Digital Tendencies

Do you bear in mind the facade you eliminated to cost the battery? Now you may put that again in place. Use the star-shaped finish of the screwdriver to position the small screw of the set up equipment into the opening positioned on the backside of the doorbell. This may stop the facade from coming off.

Lastly, activate the gadget once more. The ringing tone on the entrance of your doorbell ought to gentle up and it is best to have the ability to use the app to see what your new doorbell is seeing.





COMMENTS

Leave a Reply

Your email address will not be published. Required fields are marked *